February 2, 2023 - Fully Remote!

The biggest event of the practice today was having the robot fully remote control pick up and eject a cube. It wasn't perfect but it worked!!! That's a big deal! We can celebrate this moment and also know that it'll only get better from here! Now we have 2 weeks to get it all perfected as much as we can. Then we'll have a few more weeks after the Week Zeros to perfect/practice even more. 

Back to the important stuff. We got our 80:1 gear box in the mail today along with the gears for moving the whole intake in and out. So we spent a bunch of time taking off the old brackets, installing the new ones, figuring out spacers, putting together the gear box, installing hubs on the intake/shooter, etc. It took most of the meeting time and we didn't actually have it all together until 7:45pm haha. But it was SO COOL when it worked. Shoutout to everyone on the team having a hand in getting it ready. Also, big shoutout to Jarrod for having his math/CAD work!!

Justin and William worked on programming the intake/shooter motor, started working on vision, and other programming things. It's exciting that they'll have the ability to work on some of the autonomous and fine-tuning stuff at some point very soon. 

Gettel, Charles, and Vincent also started working on making our red set of bumpers. We had to scavenge some 3/4" plywood from the back room and then cut it down. It was an experience haha. But we need the red bumpers for Week Zeros so it's important to get done!

Electrical did some work making all the wiring look pretty and ready to go. They also worked on making a new top plate for the radio, raspberry pi, and emergency switch. Progress!! We also collected sizes for the team t-shirts. 

But yeah, it was a great practice and felt good to get all of our parts in and make some big moves. Excited to see what we'll get done on Saturday!

OH BABY


Comments

Post a Comment

Popular posts from this blog

February 11, 2023 - Rebuilding for the last (haha) time

Image
Last Saturday before Eagan! Wooo!!  Sam, Jayden, and I worked on rebuilding the intake/shooter for hopefully one of the last times. We used the new plates and it all came together wonderfully. It took a while because we had to assemble the new gearbox and hex hubs and stuff. So yeah, new shooter/intake is all ready. Our other big task was making the "hard stops" for the mechanism to be brought in and put out with a controller so we got that done as well. Matthew and Gettel worked on getting the front bumper all set. I didn't record a video because we only practiced shooting once or twice but, for the most part, the mechanical aspects of the robot are all ready to go for now. Yay! Andrew H and Matthew did a great job on electrical today. They installed the encoders that they could which included a lot of tedious soldering. They also installed the operating light on a bracket so we're all good there too. There's still some wire management to do among other things bu...
Read more

January 16, 2023 - Driving Base Robot and Prototyping

Image
 With everyone off work/school we met at the shop from 12pm to 5pm. Edward and Coach Sticht focused on programming the robot. The radio was being finicky so we didn't get to wireless driving just yet but we will soon. The robot DID drive and balanced on the charging station. YAY!!! That was the most exciting moment of the day. The rest of the group focused on moving stuff out of the back back room and prototyping. The prototyping went fairly well. We have a few general ideas for intakes and outputs. A milk carton was cut up as a basket. Jarrod and Mohamud did some math for us to figure out pivot points and arm lengths for a mid cone score. We're still working though lots of ideas but that's what this week is for!
Read more

January 28, 2023 - New Brackets, Website Updates, and a Booster Club

Image
We were hanging out doing stuff when I looked at the calendar and realized we only have 2 more Saturday meetings until our first Week Zero. WOAH! That shouldn't make any of us anxious but it definitely is wild just how fast time passes and how little time we really have until the scrimmages.  Build team did a few big things today. Sam and Jarrod worked on making our new and improved brackets for the intake/shooter. I gotta say, watching Jarrod be a wizard with CAD was pretty freaking sweet (s/o Solidworks). Also, Sam killed it making the steel brackets. They look so good. Build Team also moved the CIM motors around a few different times to try to offset the cube compression that was happening. The cube compression is causing the shooter action to not work reliably. We have a more ideas to try, not time to freak out. We are definitely on the right track (it works great when everything is lined up). We just need to keep iterating and trying to get that consistency. But we're conf...
Read more